Intimus 852 CC User Manual download pdf (Page 5)

For access safety reasons the

machine must only be operated if the

hopper extension (9) is assembled to

the hopper (10).

POWER SUPPLY CONNECTION:

a) The maximum value for loop impedance at the

mains connection point is 0.5 Ohms.

b) The conductor cross-section of the power

supply line should be of a magnitude so as

to cause a 15% voltage drop in the case of a

machine blockage (inhibit current = 6 x nominal

current).

CHECKING THE RUNNING DIRECTION:

1. Move the main switch (1) (ﬁg. 1) to position

„1“.

2. Press the „forward“ button (2) (ﬁg. 2). The

cutting system starts running.

3. Check that the cutting system is running in the

correct direction and correct the phase relation

of the power plug if necessary.

Correcting the phase relation of the

power plug may only be carried out

by a qualiﬁed electrician!

Now that everything has been correctly assembled

and connected, you can proceed to operating

the machine.

IMPORTANT SAFETY PRECAUTIONS

<< Danger of injury! Keep all loose articles of

clothing, ties, jewelery, long hair or other

loose objects away from opening!

<< Danger of injury! Never insert ﬁngers into ope-

ning!

<< In case of danger switch the machine off with the

mains switch, or with the emergency switch, or

unplug the machine!

<< Always unplug the machine from the mains power

supply before opening the machine!

Repairs may only be performed by trained per-

sonnel!

<< The machine may not be operated by more than

one person at any given time!

The machine was designed for safe operation by “one

person only”.

<< During the shredding process no other work

may be performed on the machine (for example

cleaning, etc.)!

<< The machine is not a toy, and is not suitable for

use by children!

The overall technical safety concept of this machine

(dimensions, feed openings, emergency shutdown

devices etc.) does not provide for any guarantee

regarding hazard-free operation by children.

APPLICATION:

The INTIMUS 802CC/852CC shredder is used in

all areas where large quantities of printed material

need to be shredded.

The machine (model 852CC) can shred card

board and crumpled paper as easily as it shreds

smooth paper.

The shredder should only be fed with

paper or cardboard!

Shredding other data carriers can cause

injury(e.g. by splintering of hard materials)

or may damage the shredder (e.g. des-

truction of the cutting system).

INSTALLATION REQUIREMENTS:

Note: Be certain that three phase current is

available at the point of installation (see TECH

NICAL DATA for information concerning required

pre-fusing of the electrical outlet).

Proceed as follows:

- Unpack and set machine upright.

- Mount the hopper extension (9) (see description

below).

- Put the collecting bag into the sliding frame (see

description „EMPTYING THE COLLECTING

BAG“)

- Plug in the machine.

The air vents in the housing are ne-

cessary for cooling and may not be

covered or closed!

The mains connection at the machine

must be freely accessible!

Only operate the machine in enclosed

rooms at temperatures between 10°C

and 25°C!

ASSEMBLY OF THE HOPPER EXTENSION:

(Fig. 3) (Model 852CC)

Take the hopper extension (9) out of the cabinet

and place it as shown on top of the hopper (10).

Fix the hopper extension with the four provided

screws to the hopper itself.

Fig. 1

Fig. 2

2 5 6 7

802CC

852CC

Fig. 3

82810 10 10/11

INITIAL START UP

MAINS SWITCH

Translation of the Original Operation Manual

Übersetzung der Originalbetriebsanleitung

1 2 3 4 5 6 7 8 9 10 ... 55 56

Comments to this Manuals

No comments

Intimus 852 CC User Manual Page 5

Comments to this Manuals

Related products and manuals for Shredders Intimus 852 CC